產品名稱：Aim-TTi TGR6000 6000MHz 波形發生器

Technical specification

Frequency

Frequency Range

10MHz to 6000MHz

Setting Resolution

10Hz by direct keyboard entry, or in user-set increments of 10Hz to 999?999MHz by rotary control or increment–decrement keys

Phase Noise

500MHz Carrier: <-110dBc/Hz @ 20kHz offset; <-120dBc/Hz @ 100kHz

3GHz Carrier: <-95dBc/Hz @ 20kHz offset; <-110dBc/Hz @ 100kHz offset

6GHz Carrier: <-89dBc/Hz @ 20kHz offset; <-104dBc/Hz @ 100kHz offset

Residual FM

Equivalent peak deviation for 300Hz to 3.4kHz B/W: 12Hz at 500MHz carrier

Settling Time

<8ms to settle within 100Hz or 0.1ppm of final frequency, if greater

Reference Frequency

Internal or External (via rear panel BNC)

Internal Accuracy

+/- 1 ppm over 15°C to 30°C; +/- 2 ppm over 5°C to 40°C

Internal Stability

< +/-1ppm/year ageing

Internal Ref. Out

10MHz from 50 Ohms, amplitude 2V pk-pk into 50 Ohms

External Ref In

10MHz into 50 Ohms, amplitude 2V pk-pk to 5V pk-pk

Output Level

Level Range

–110dBm to +7dBm (0.1μV to 500mV into 50 Ohms)

Setting Resolution

0.1dB (or 0.01μV to 1mV) by direct keyboard entry, or in user-set increments of 0.1dB to 100dB (or 0.01μV to 100mV)

Accuracy

Better than ± 2dBm

Harmonics

<-25dBc at +7dBm. <-30dBc@levels <=0dBm 30 to 6000MHz, <-25dBc@levels <=0dBm 10 to 30MHz

Sub-Harmonics

<3000MHz : None. >3000MHz :<–40dBc (typ) @ +7dBm

Non-Harmonic Spurii

<–50dBc >10kHz offset 10 to 3000MHz, <-44dBc >10kHz offset 3000MHz to 6000MHz

Output Connector

Type N

Sweep

Frequency and amplitude sweep

Step Sweep

Step frequency and/or amplitude according to a formula over a specified number of points

Dwell Time

Individually programmable 0.01 to 10.000sec per step

Max Points

1000

Sweep Run

Continuous or single. Sweep up or down

Step Spacing

Linear or logarithmic

Sweep Triggering

Manual, Ext. signal, timed (0.1 – 999.9sec) or via remote interface

Sync Signal

Output Stable) available during dwell time. Programmable as high or low

List Sweep

As for Step Sweep except that a user defined table of frequency, amplitude and dwell time values defines the steps. The table can be created within the instrument or downloaded via the remote interfaces

Max Points

1000

List Storage

Up to 16 Sweep Lists can be stored permanently within the instrument

Point Trigger

Each point in a sweep (step or list) can be subject to a trigger event rather than a dwell time. Trigger by Manual, Ext. signal or via remote interface

Trim

(User Level Compensation Tables)

Function

A table of frequency/gain pairs allows the user to modify the generator output level with respect to frequency to calibrate an entire test set up or improve the calibration of the generator alone

Max Points

100

Interfaces

Full digital remote control through the RS232, USB, LAN and GPIB interfaces

RS-232

9-pin D connector. Variable Baud rate 1200 and 115200 Baud

USB

USB 2.0 connection. Operates as a virtual COM port

GPIB (IEEE-488)

Conforming with IEEE488.1 and IEEE488.2

LAN (Ethernet)

Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol

General

Size and Weight

2U (86.5mm) height; half-rack (213mm) width; 350mm long. 3.65 kg. (8 lb)

Power

110-240VAC ±10% 50/60Hz; 100-120VAC ±10% 400Hz; 60VA max

Approvals

Complies with EN 61010-1 (Safety) and EN61326 (EMC)